thingiverse
Spring Flinger
Spring-loaded projectile launcher. This was designed as a thought starter about harness...
spring aligner 3D Models
499 resultsSponsored
thingiverse
myminifactory
Spring Cup aligner Ender-2
For Creality Ender 2 With this Spring aligner for the bed leveling you get more precis...
thingiverse
Spring Cup aligner Ender-2
With this Spring aligner for the bed leveling you get more precise leveling and a more ...
cults3d
compound string and cam aligner
parts needed https://www.amazon.co.uk/gp/product/B07FW26HD4/ref=ppx_yo_dt_b_asin_title_...
thingiverse
Jazz Bass 4 String Pickup Magnet Aligner - Bridge & Neck
https://www.youtube.com/watch?v=6kD9PRZIYzY&t=234s This thing is used to align magne...
thingiverse
4 Stroke Engine Model Improved Cam Shaft
After building the 4 Stroke engine model by Zockzock I ran into the same problem as Bou...
SPONSORED
🪙 Will Bitcoin cross $200,000 in 2026?
Crypto traders are betting big. Will BTC hit the milestone?
grabcad
Trailer Torsion Axle design
Trailer Torsion Axle design - Stelu Harsan - 2011.08.28Features (dimensions are in mm):...
thingiverse
Voron V0 spring steel alignment
A simple mod using bolts and square nuts to keep you spring steel sheet aligned. Don't...
thingiverse
Talon Fang U
I am going to post new makes on my prusa account, thingiverse is making it too hard to ...
prusaprinters
Worker Cheetah Smooth Trigger
A better trigger for the Worker Cheetahstronger, more comfortable Prints without suppor...
thingiverse
Wire and Plug holding fixture
These holders help keep the wires aligned with small plugs that need to be soldered. Al...
thingiverse
BLTouch Support for Wanhao i3 Plus and ADVi3++ - EXTENDED
Lowered version of the original by andrivet designed to be used with the supplied sprin...
thingiverse
DP5 Bits & Pieces
A couple of bits for my DMS DP5, a snap in 2020 dual cable clip, and a set of washers f...
thingiverse
DP5 Bits & Pieces
A couple of bits for my DMS DP5, a snap in 2020 dual cable clip, and a set of washers f...
cults3d
BLTouch Support for Wanhao i3 Plus and ADVi3++ - EXTENDED
Lowered version of the original by andrivet designed to be used with the supplied sprin...
grabcad
Trailer Torsion Axle design - Stelu Harsan - 11 08 28
Trailer Torsion Axle design - Stelu Harsan - 11 08 28 Features (dimensions are in mm): ...
thingiverse
Ender-2 Heat Bed Insulation Pattern
This pattern can be used to lasercut or hand cut insulation to fit the heated bed of th...
thingiverse
Replicator HBP Washer Constraints
A set of 4 constraints for the Replicator's HBP washers. It can be a real chore to keep...
thingiverse
FlyingBear Ghost Easy glass bed removal corner guides
I separated layers of garbage from original setup of this bed and simply placed glass b...
grabcad
truck chassis
All dimensions where calculated and designed required to for more than 12 tones capacit...
thingiverse
Self locking Y belt holder for Anet A8
This is a self locking belt holder for Anet A8. The belt height is aligned with the pul...
thingiverse
Biohazard Spring Thunder Project WIP
slight modification of the body, internals, and shells allowing for shells with more st...
thingiverse
Mk3 A70 Supra front badge retainer clip
The front badge retainer clip has a tendency to rust away. This plastic clip does the s...
thingiverse
190mm Shock Absorber
I needed a mock-up for a shock absorber so I modeled one up and it actually works quite...
thingiverse
Spring Clip
Newer version. Hard to say where the spring part will be most effective. This is edi...
thingiverse
spring corner design FFCPV3
2019-12-9: The PETG version works ok for printing with a 70C bed, but not for 100C bed ...
prusaprinters
Spring Powered Coaxial Rotorcraft
NOTE: this is not currently flying. I am going to totally redesign it optimized for a b...
thingiverse
Kcs low power electrical push push switch
This low power electrical switch is part of a reading lamp that I'm designing. My des...
thingiverse
Z Limiter Zonestar P802Q
On my zonestar the Z axis tuning is VERY annoying. Mainly because the screw is too sh...
thingiverse
3x3x3 Speed Cube
Speedcube V.0.71 ----------------------- The goal is to design a Speed-Cube 100% pr...
Sponsored
Sponsored